Feser TFC Xtender 120mm Radiator Shroud
The Blue Led Module does not have to be instaled if not desiered if your are not into the Bling Bling!
The Blue Led Module does not have to be instaled if not desiered if your are not into the Bling Bling!
Feser TFC Xtender 120mm Radiator Shroud
Product Description:
The Xtender tunnel reduces fan dead space and improves the airflow through a radiator. The air turbulence is increased within this tunnel volume and
eliminates the dead spot below the middle of the impeller. Another adavatage is noise level is reduced significantly as well approximately 5-7 decibels.
The Xtender is a Multi-LED-Radiator Shroud for use with 120mm Fans. For raditators with multiple 120mm fans more than one TFC Extenter can be used.
Features:
The Xtender tunnel reduces fan dead space and improves the airflow through a radiator as well as reduces sound level. The air turbulence is increased
within this tunnel volume and eliminates the dead spot below the middle of the impeller.
IMPORTANT NOTES & INSTALLATION GUIDE!
1. Improve performance in both a Push or Pull setup. A slight performance gain is in the Pull setup.
2. It is always better for the cooling performance, to push/pull ambient temperature into the case and through the radiator.
3. The supplied screws are 4x M3/65mm and 4x M4/65mm and selected for use with 120x120x25mm fans. M3 screws are used for our Xchanger Series. M4
should work with other rads. Screws are not supplied for fans with 38mm height. **Note** M4 screws are a tight fit and some force is needed to install.
4. Use the supplied silicon pad/noise absorber between Xtender and fan. Currently designed with the 17mm fan hole spacing but can be trimmed for 15mm
radiator fan spacing.
MOUNTING ORDER:
1. Xchanger Radiator (or other brand)
2. Silicone Pad (supplied with radiator - in our case Xchanger)
3. Xtender Shroud
4. Silicone Pad - supplied with Xtender
5. Fan
6. Washer
7. Screw
Install the LED Module after you installed the Radiator properly.
Included Components:
- One TFC Xtender Acrylic Shroud
- Four Mounting Screws
- One Clear 120mm Gasket
- Blue Led Module
The Xtender tunnel reduces fan dead space and improves the airflow through a radiator. The air turbulence is increased within this tunnel volume and
eliminates the dead spot below the middle of the impeller. Another adavatage is noise level is reduced significantly as well approximately 5-7 decibels.
The Xtender is a Multi-LED-Radiator Shroud for use with 120mm Fans. For raditators with multiple 120mm fans more than one TFC Extenter can be used.
Features:
- It can be used with any Radiator available on the market with standard 120mm dimensions.
- It has 2 LED mounts for use with supplied LED Module.
- LED Mounts are designed for standard LEDs. Customization with other 5mm LED's is possible.
- It consists of pure PMMA Acrylic Material.
- By mounting this item on a radiator, it will increase the cooling performance up to 20%
- Reduce noise by lowering fan speed
- Dimensions: 120 x 120 x 31 mm
- Weight: 106g
The Xtender tunnel reduces fan dead space and improves the airflow through a radiator as well as reduces sound level. The air turbulence is increased
within this tunnel volume and eliminates the dead spot below the middle of the impeller.
IMPORTANT NOTES & INSTALLATION GUIDE!
1. Improve performance in both a Push or Pull setup. A slight performance gain is in the Pull setup.
2. It is always better for the cooling performance, to push/pull ambient temperature into the case and through the radiator.
3. The supplied screws are 4x M3/65mm and 4x M4/65mm and selected for use with 120x120x25mm fans. M3 screws are used for our Xchanger Series. M4
should work with other rads. Screws are not supplied for fans with 38mm height. **Note** M4 screws are a tight fit and some force is needed to install.
4. Use the supplied silicon pad/noise absorber between Xtender and fan. Currently designed with the 17mm fan hole spacing but can be trimmed for 15mm
radiator fan spacing.
MOUNTING ORDER:
1. Xchanger Radiator (or other brand)
2. Silicone Pad (supplied with radiator - in our case Xchanger)
3. Xtender Shroud
4. Silicone Pad - supplied with Xtender
5. Fan
6. Washer
7. Screw
Install the LED Module after you installed the Radiator properly.
Included Components:
- One TFC Xtender Acrylic Shroud
- Four Mounting Screws
- One Clear 120mm Gasket
- Blue Led Module
 |
|||||||||
 |
 |
 |
 |
 |
 |
 |
|||
 |
 |
 |
 |
||||||